| Battery cover install
The “Fastlane Battery Cover” installation is very easy, first remove the lower hood gasket just to expose the battery area. The FBC is designed to be a tight fit so you may need to pull your lower intake back a bit. Next slide the side tabs between the battery and battery insulation wrap on the left side till the top touches the top of the battery hold down. Replace the lower hood gasket and your done! NOTE!! You also might want to put a piece of tape where the battery hold down touches the cover to avoid any scratching! |
Front Door Applique Removal Procedure 1. Open the front door. 2. Remove the screw attaching the outside belt weather-strip, and then remove the weather-strip from the door. 3. Remove the glass run weather-strip as necessary to access the three screws attaching the applique. 4. Remove the three screws attaching the applique, and then remove the applique from the door. Installation Procedure 1. Place the applique into position. 2. Install the three attaching screws. 3. Install the glass run weather-strip into position. 4. Place the outside belt weather-strip into position and install the attaching screw. 5. Close the door. Rear Door Applique Removal Procedure 1. Open the rear door. 2. Lower the door window to its lowest position. 3. Remove the front and rear screws attaching the outside belt weather-strip, and then remove weather-strip from the door. 4. Remove the glass run weather-strip as necessary to access the three screws in the B-pillar applique. The glass run weather-strip will need to be free of the glass on the forward edge, so that the front edge of the glass can push outward to access the lower screw. 5. Place a shop towel between the tract and glass so that the screws do not fall down in to the door opening. 6. Remove screws attaching B-pillar applique, and then remove the applique from the door. 7. To remove C-pillar applique pull the glass run weather-strip down as necessary to access the three screws in the C-pillar applique. 8. Remove the screws attaching C-pillar applique, and then remove the applique from the door. Installation Procedure 1. Position the C-pillar applique on the door. 2. Install the attaching screws to C-pillar. 3. Install the C-pillar applique glass run weather-strip into position. 4. Position the B-pillar applique on the door. 5. Place a shop towel between the tract and glass so that the screws do not fall into the door opening. 6. Install the attaching screws to B-pillar applique. 7. Install the glass run weather-strip into position on the door frame. *** Important note*** Be very careful when removing these as I refinish and paint these for the next customer. It's ok if they are scratched or the finish is bad but If they are dented they cannot be fixed or used again. If this is the case the damaged ones will be returned and the core refund will be pro-rated. |
| Door Pillars |
| Invisible scoop install Instructions
• Remove the left front wheel • Remove the 3 screws holding the front lower fender well in place as well as the panel for headlight bulb replacement. • Attach the scoop just below the opening using the 2 sided tape and self tapping screws provided *Note – Use alcohol to prep the area for the 2 sided tape (attached) Make sure to use the self tapping screws (provided) only tighten, do not torque!!, The tape is 3M but with the air pressure exerted I can’t promise it would stay. • There is an opening just below the fog light, pull back the fender well and feed the hose up to the hole in the fender well. Once the hose is snapped into the fender well hole you just need to arrange the hose, the hose has been flattened but is flexible to accommodate the space provided, the only obstacles will be the fog light and some wires. • Now the easy part, push the fender well back into place and replace the screws making sure to snap the upper part of the lower fender well back in place as well as the panel for bulb replacement. |
| Mirrored Hood Liner The hood liner comes with Industrial strength Velcro, 2 at the top and 2 on the sides. The center bottom piece is 2"x2" and goes on the insulation hold down. You must initially set up your liner by removing the 4 backing pieces from the hood liner and sticking the 2x2 piece to the hood insulation hold down with the rough side up, (pictured below) this will assure proper alignment of this piece. Clean the hood surface edge to remove any dirt etc. Using the top edge align the mirror to the hood then press the bottom center to mount that part. Remove the mirror leaving the hard plastic side of the velcro on the hood. Press both sides down to insure a good seal on the hood and the mirror. Let sit for approxamatly 12 hours so the glue will set up. When mounting the mirror align the top, sides and press the center bottom part in place, the while holding the center bottom disengage and reattach the 2 sides to release tension from the center, if you do not do this the center bottom will come loose. Always store you hood liner in it's felt lined sleeve to avoid scratching ENJOY YOUR "FASTLANE" HOOD MIRROR!! |
 |